EuropeUSA 904 oils in 35 classes + 187 American oils in 10 classes SK · EN · DE · PL · Contact
Engine oil technical data · Motul

MOTUL 8100 Eco-clean 5W-30

MOTUL 8100 Eco-clean 5W-30 is a 5W-30 C3 engine oil (ACEA C2 · API SN). According to the manufacturer's data sheet it has a viscosity of 61 mm²/s at 40 °C, 11 mm²/s at 100 °C, a viscosity index of 164, HTHS of 3 mPa·s, a TBN of 8 mg KOH/g, a pour point of −36 °C and sulphated ash of 0.8 %.

Data sheet ↗ Data verified: 8 Nov 2026

✎ Found an error? Report it

Parameters from the data sheet

ParameterValueClass median 5W-30 C3 i
Viscosity 40 °C61 mm²/s70 mm²/s
Viscosity 100 °C11 mm²/s12 mm²/s
Viscosity index164 168
TBN8 mg KOH/g7.4 mg KOH/g
CCS −30 °Cnot stated
Pour point−36 °C−42 °C
Flash point240 °C230 °C
Density0.847 g/cm³Density is given at 20 °C (most manufacturers state it at 15 °C).0.851 g/cm³
HTHS 150 °C3 mPa·s3.5 mPa·s
Sulphated ash0.8 %0.795 %

All 5W-30 C3 oils → See the class table for a detailed comparison with other oils.

Specifications and approvals

Specification
ACEA C2 · API SN
Oils by specification

Similar oils

Oils in the 5W-30 C3 class with the closest parameters and the same specification.

Oil analysis

We wrote this text by comparing the data-sheet values with the other oils in the 5W-30 C3 class.

MOTUL 8100 Eco-clean 5W-30 is a motor oil from Motul, viscosity grade 5W-30. In the database we compare it with 120 other oils in the 5W-30 C3 class.

The oil meets ACEA C2, API SN, Fiat 9.55535-S1, PSA B71 2290. ACEA C2 is a low-ash oil with reduced HTHS (from 2.9 mPa·s) for DPF engines where the carmaker wants lower friction. API SN is an older American specification for petrol engines.

Viscosity at 100 °C is 11 mm²/s, in the middle of the 9.3–12.5 mm²/s range for the summer grade 30.

Strengths: TBN 8 mg KOH/g is in the top quarter of the class (median 7.4); flash point 240 °C is among the best 10 % in the class (median 230).

Weaker values: viscosity index 164 is in the weaker half of the class (median 168); HTHS 3 mPa·s is among the weakest in the class (median 3.5); pour point −36 °C is among the weakest in the class (median −42).

Limit values: HTHS 3 mPa·s is below 3.5 mPa·s; the oil is meant for engines where the carmaker specifies low HTHS; sulphated ash of 0.8 % is suitable for engines with a DPF.

Based on its values it suits engines with a DPF. The high flash point suggests low volatility and lower oil consumption. The specification or approval in your vehicle manual always has the final word.

The data sheet does not state Noack volatility, so we cannot compare it on this parameter.