EuropeUSA 904 oils in 35 classes + 187 American oils in 10 classes SK · EN · DE · PL · Contact
Engine oil technical data · Xenum

XENUM X1 5W-30

XENUM X1 5W-30 is a 5W-30 C3 engine oil (ACEA C2, C3). According to the manufacturer's data sheet it has a viscosity of 74.3 mm²/s at 40 °C, 12.4 mm²/s at 100 °C, a viscosity index of 166, a TBN of 7.6 mg KOH/g, a pour point of −39 °C and sulphated ash of 0.67 %.

Data sheet ↗ Data verified: 8 Nov 2026

✎ Found an error? Report it

Parameters from the data sheet

ParameterValueClass median 5W-30 C3 i
Viscosity 40 °C74.3 mm²/s70 mm²/s
Viscosity 100 °C12.4 mm²/s12 mm²/s
Viscosity index166 168
TBN7.6 mg KOH/g7.4 mg KOH/g
CCS −30 °C6060 mPa·s5881 mPa·s
Pour point−39 °C−42 °C
Flash point225 °C230 °C
Density0.848 g/cm³0.851 g/cm³
HTHS 150 °Cnot statedNot stated by the manufacturer. ACEA C3 requires at least 3.5 mPa·s.
Sulphated ash0.67 %0.795 %

All 5W-30 C3 oils → See the class table for a detailed comparison with other oils.

Specifications and approvals

Specification
ACEA C2, C3
Oils by specification

Similar oils

Oils in the 5W-30 C3 class with the closest parameters and the same specification.

Oil analysis

We wrote this text by comparing the data-sheet values with the other oils in the 5W-30 C3 class.

XENUM X1 5W-30 is a motor oil from Xenum, viscosity grade 5W-30. In the database we compare it with 120 other oils in the 5W-30 C3 class.

The oil meets ACEA C2, ACEA C3, BMW LL-04, MB 229.51 and more (9 in total). ACEA C2 is a low-ash oil with reduced HTHS (from 2.9 mPa·s) for DPF engines where the carmaker wants lower friction. ACEA C3 means a mid-SAPS oil (max 0.8 % ash) with HTHS of at least 3.5 mPa·s for petrol and diesel engines with a particulate filter. VW 504 00 / 507 00 are VW Group approvals for engines with extended LongLife service intervals. MB 229.51 is the Mercedes-Benz approval for engines with a DPF.

Viscosity at 100 °C is 12.4 mm²/s, near the upper end of the 9.3–12.5 mm²/s range for the summer grade 30. Within its class the oil is on the thick side, with more reserve at high temperatures.

Average values: viscosity index 166 is close to the class middle (median 168); TBN 7.6 mg KOH/g is close to the class middle (median 7.4); flash point 225 °C is close to the class middle (median 230).

Weaker values: CCS 6060 mPa·s is in the weaker half of the class (median 5850); pour point −39 °C is in the weaker half of the class (median −42).

Limit values: CCS 6060 mPa·s at −30 °C is 92 % of the SAE limit (6600 mPa·s); sulphated ash of 0.67 % is suitable for engines with a DPF.

Based on its values it suits engines with a DPF and higher loads, towing or high-mileage engines. The specification or approval in your vehicle manual always has the final word.

The data sheet does not state HTHS and Noack volatility, so we cannot compare it on these parameters.