Oil viscosity and temperature: SAE chart 0W to 25W, 20 to 60
How cold it can get before an engine with 0W, 5W or 10W oil struggles to start, what the second number means and what viscosity oils have at 40 and 100 °C. Limits from SAE J300 and typical values from our database.
The first number (W): cold start
The number before the letter W tells you down to which temperature the oil stays fluid enough for the starter to crank the engine and for the pump to deliver oil to the bearings. SAE J300 checks this with two tests: CCS (cranking simulator) and MRV (pumpability). The last column is a practical summary, not a value from the standard.
| SAE grade | CCS max (cranking) | Pumpability (MRV) | Cold start down to about |
|---|---|---|---|
| 0W | 6,200 mPa·s at −35 °C | −40 °C | −35 °C |
| 5W | 6,600 mPa·s at −30 °C | −35 °C | −30 °C |
| 10W | 7,000 mPa·s at −25 °C | −30 °C | −25 °C |
| 15W | 7,000 mPa·s at −20 °C | −25 °C | −20 °C |
| 20W | 9,500 mPa·s at −15 °C | −20 °C | −15 °C |
| 25W | 13,000 mPa·s at −10 °C | −15 °C | −10 °C |
Each step between grades is 5 °C. A 0W oil is not essential in a Central European winter, but it helps on every cold start because it reaches the bearings faster.
The second number: viscosity at operating temperature
The number after the dash is not about outside temperature. It sets the range of kinematic viscosity at 100 °C and the minimum HTHS viscosity at 150 °C, the temperature in bearings and around the pistons.
| SAE number | Viscosity at 100 °C (mm²/s) | HTHS at 150 °C min (mPa·s) |
|---|---|---|
| 8 | 4.0 to < 6.1 | 1.7 |
| 12 | 5.0 to < 7.1 | 2.0 |
| 16 | 6.1 to < 8.2 | 2.3 |
| 20 | 6.9 to < 9.3 | 2.6 |
| 30 | 9.3 to < 12.5 | 2.9 |
| 40 | 12.5 to < 16.3 | 3.5 (0W/5W/10W-40), 3.7 (15W/20W/25W-40) |
| 50 | 16.3 to < 21.9 | 3.7 |
| 60 | 21.9 to < 26.1 | 3.7 |
SAE does not define an upper ambient temperature. xW-40 and xW-50 oils are sometimes described as suited to hot climates, but the deciding factor is the carmaker's specification, not the summer.
Typical viscosity at 40 °C and 100 °C
The table shows medians from the data sheets of the oils in our database. At 40 °C oil is about five to eight times thicker than at 100 °C. The viscosity index shows how much viscosity changes with temperature: the higher it is, the less the oil thickens in the cold and thins in the heat.
| Grade | Oils | At 40 °C (mm²/s) | At 100 °C (mm²/s) | Viscosity index |
|---|---|---|---|---|
| 0W-16 | 20 | 37 | 7.3 | 162 |
| 0W-20 | 32 | 44 | 8.3 | 173 |
| 0W-30 | 41 | 58 | 10.4 | 181 |
| 0W-40 | 38 | 76 | 13.4 | 182 |
| 5W-20 | 20 | 45 | 8.2 | 161 |
| 5W-30 | 159 | 70 | 11.9 | 168 |
| 5W-40 | 112 | 86 | 14.1 | 172 |
| 5W-50 | 29 | 114 | 18.0 | 180 |
| 10W-30 | 13 | 78 | 12.0 | 143 |
| 10W-40 | 103 | 97 | 14.3 | 154 |
| 10W-50 | 10 | 117 | 17.5 | 165 |
| 15W-40 | 24 | 107 | 14.6 | 138 |
Values for individual oils are in the table of each class, where you can sort and compare them.