Valvoline Advanced Full Synthetic 5W-30
Valvoline Advanced Full Synthetic 5W-30 is a 5W-30 engine oil (ACEA A5/B5 · API SN · ILSAC GF-5). According to the manufacturer's data sheet it has a viscosity of 60.1 mm²/s at 40 °C, 10.2 mm²/s at 100 °C, a viscosity index of 158, HTHS of 3.2 mPa·s, a TBN of 9.3 mg KOH/g and sulphated ash of 0.97 %.
Data sheet ↗ Data verified: 19 Nov 2026
Parameters from the data sheet
| Parameter | Value | Class median 5W-30 i |
|---|---|---|
| Viscosity 40 °C | 60.1 mm²/s | 61.2 mm²/s |
| Viscosity 100 °C | 10.2 mm²/s | 10.7 mm²/s |
| Viscosity index | 158 | 166 |
| TBN | 9.3 mg KOH/g | 8.6 mg KOH/g |
| CCS −30 °C | 6000 mPa·sThe manufacturer gives only a limit, "less than 6000", not a measured value. | 4965 mPa·s |
| Pour point | −36 °CThe manufacturer gives only a limit, "at most −36", not a measured value. | −42 °C |
| Flash point | not stated | |
| Density | not stated | |
| HTHS 150 °C | 3.2 mPa·s | 3.2 mPa·s |
| Sulphated ash | 0.97 % | 0.87 % |
| Noack volatility | 9.3 % |
All 5W-30 oils → See the class table for a detailed comparison with other oils.
Specifications and approvals
- Specification
- ACEA A5/B5 · API SN · ILSAC GF-5
- Oils by specification
Similar oils
Oils in the 5W-30 class with the closest parameters and the same specification.
- Royal Purple High Performance 5W-30API SQ · ILSAC GF-7A
- Valvoline Full Synthetic High Mileage MaxLife 5W-30API SP · ILSAC GF-6A
- Valvoline Extended Protection 5W-30API SP · ILSAC GF-6A
- Amsoil Signature Series 5W-30API SQ, SP, SN Plus · ILSAC GF-7A, GF-6A, GF-5
- DuraMAX Synthetic Gen 3 5W-30API SP · ILSAC GF-6A
- Kendall GT-1 Endurance 5W-30API SN · ILSAC GF-5
Oil analysis
We wrote this text by comparing the data-sheet values with the other oils in the 5W-30 class.
Valvoline Advanced Full Synthetic 5W-30 is a motor oil from Valvoline, viscosity grade 5W-30. In the database we compare it with 44 other oils in the 5W-30 class.
The oil meets API SN, ILSAC GF-5, ACEA A5/B5, GM dexos1 Gen2 and more (6 in total). API SN is an older American specification for petrol engines. ILSAC GF-5 is an older US–Japanese specification for fuel-efficient petrol engines. ACEA A5/B5 is a fuel-economy specification with reduced HTHS for engines without a DPF. GM dexos1 is the General Motors licence for petrol engines. Chrysler MS-6395 is the Stellantis approval for Jeep, Dodge, RAM and Chrysler petrol engines.
Viscosity at 100 °C is 10.2 mm²/s, near the lower end of the 9.3–12.5 mm²/s range for the summer grade 30. Within its class the oil is on the thin side, which helps fuel economy.
Average values: HTHS 3.2 mPa·s is close to the class middle (median 3.2); TBN 9.3 mg KOH/g is close to the class middle (median 8.6); Noack volatility 9.3 % is close to the class middle (median 9.4).
Weaker values: viscosity index 158 is in the weaker half of the class (median 166).
Limit values: HTHS 3.2 mPa·s meets the 2.9 mPa·s minimum required for this class; sulphated ash of 0.97 % is higher; the oil is not intended for engines with a DPF.
Based on its values it suits engines without a DPF and everyday driving where fuel economy matters most. The specification or approval in your vehicle manual always has the final word.