EuropeUSA 904 oils in 35 classes + 187 American oils in 10 classes SK · EN · DE · PL · Contact
Engine oil technical data · Eurol

Eurol Syntence FS 0W-30

Eurol Syntence FS 0W-30 is a 0W-30 engine oil (ACEA C3). According to the manufacturer's data sheet it has a viscosity of 68.3 mm²/s at 40 °C, 12.2 mm²/s at 100 °C, a viscosity index of 178, HTHS of 3.5 mPa·s, a TBN of 8.3 mg KOH/g, a pour point of −51 °C and sulphated ash of 0.8 %.

Data sheet ↗ Data verified: 8 Nov 2026

✎ Found an error? Report it

Parameters from the data sheet

ParameterValueClass median 0W-30 i
Viscosity 40 °C68.3 mm²/s58 mm²/s
Viscosity 100 °C12.2 mm²/s10.4 mm²/s
Viscosity index178 181
TBN8.3 mg KOH/g8.4 mg KOH/g
CCS −35 °Cnot stated
Pour point−51 °C−48 °C
Flash point239 °C226 °C
Density0.84 g/cm³Density is given at 20 °C (most manufacturers state it at 15 °C).0.843 g/cm³
HTHS 150 °C3.5 mPa·s3.1 mPa·s
Sulphated ash0.8 %0.8 %

All 0W-30 oils → See the class table for a detailed comparison with other oils.

Specifications and approvals

Specification
ACEA C3
Oils by specification

Similar oils

Oils in the 0W-30 class with the closest parameters and the same specification.

Oil analysis

We wrote this text by comparing the data-sheet values with the other oils in the 0W-30 class.

Eurol Syntence FS 0W-30 is a motor oil from Eurol, viscosity grade 0W-30. In the database we compare it with 47 other oils in the 0W-30 class.

The oil meets ACEA C3, VW 504 00, VW 507 00, VW 503 00 and more (10 in total). ACEA C3 means a mid-SAPS oil (max 0.8 % ash) with HTHS of at least 3.5 mPa·s for petrol and diesel engines with a particulate filter. VW 504 00 / 507 00 are VW Group approvals for engines with extended LongLife service intervals. MB 229.51 is the Mercedes-Benz approval for engines with a DPF.

Viscosity at 100 °C is 12.2 mm²/s, near the upper end of the 9.3–12.5 mm²/s range for the summer grade 30. Within its class the oil is on the thick side, with more reserve at high temperatures.

Strengths: flash point 239 °C is among the best 10 % in the class (median 230).

Average values: HTHS 3.5 mPa·s is close to the class middle (median 3.1); pour point −51 °C is close to the class middle (median −48).

Weaker values: viscosity index 178 is in the weaker half of the class (median 181); TBN 8.3 mg KOH/g is in the weaker half of the class (median 8.4).

Limit values: HTHS 3.5 mPa·s meets the 2.9 mPa·s minimum required for this class; sulphated ash of 0.8 % is suitable for engines with a DPF.

Based on its values it suits engines with a DPF and higher loads, towing or high-mileage engines. The high flash point suggests low volatility and lower oil consumption. The specification or approval in your vehicle manual always has the final word.

The data sheet does not state Noack volatility, so we cannot compare it on this parameter.