EuropeUSA 904 oils in 35 classes + 187 American oils in 10 classes SK · EN · DE · PL · Contact
Engine oil technical data · Rowe

Rowe HIGHTEC SYNT RS HC-B SAE 5W-30

Rowe HIGHTEC SYNT RS HC-B SAE 5W-30 is a 5W-30 engine oil (ACEA A3/B4 · API SL, CF). According to the manufacturer's data sheet it has a viscosity of 73.3 mm²/s at 40 °C, 12.3 mm²/s at 100 °C, a viscosity index of 166, HTHS of 3.67 mPa·s, a TBN of 10.9 mg KOH/g and a pour point of −42 °C.

Data sheet ↗ Data verified: 8 Nov 2026

✎ Found an error? Report it

Parameters from the data sheet

ParameterValueClass median 5W-30 i
Viscosity 40 °C73.3 mm²/s68.55 mm²/s
Viscosity 100 °C12.3 mm²/s11.7 mm²/s
Viscosity index166 168
TBN10.9 mg KOH/g10.2 mg KOH/g
CCS −30 °C6180 mPa·s5927 mPa·s
Pour point−42 °C−42 °C
Flash point220 °CThe manufacturer gives only a limit, "more than 220", not a measured value.225 °C
Density0.855 g/cm³0.852 g/cm³
HTHS 150 °C3.67 mPa·s3.5 mPa·s
Sulphated ashnot statedNot stated by the manufacturer. ACEA A3/B4 allows at most 1.6 %.
Noack volatility9.1 %

All 5W-30 oils → See the class table for a detailed comparison with other oils.

Specifications and approvals

Specification
ACEA A3/B4 · API SL, CF
Oils by specification

Similar oils

Oils in the 5W-30 class with the closest parameters and the same specification.

Oil analysis

We wrote this text by comparing the data-sheet values with the other oils in the 5W-30 class.

Rowe HIGHTEC SYNT RS HC-B SAE 5W-30 is a motor oil from Rowe, viscosity grade 5W-30. In the database we compare it with 34 other oils in the 5W-30 class.

The oil meets ACEA A3/B4, API SL, API CF, BMW LL-01 and more (11 in total). ACEA A3/B4 is for high-performance petrol and diesel engines without a DPF, with HTHS of at least 3.5 mPa·s. MB 229.5 is the Mercedes-Benz approval for engines without a DPF with extended intervals. Renault RN0700 and RN0710 are Renault/Dacia approvals for petrol and older diesel engines.

Viscosity at 100 °C is 12.3 mm²/s, near the upper end of the 9.3–12.5 mm²/s range for the summer grade 30. Within its class the oil is on the thick side, with more reserve at high temperatures.

Strengths: HTHS 3.7 mPa·s is in the top quarter of the class (median 3.5); TBN 10.9 mg KOH/g is in the top quarter of the class (median 10.2).

Average values: pour point −42 °C is close to the class middle (median −42).

Weaker values: viscosity index 166 is in the weaker half of the class (median 168); CCS 6180 mPa·s is in the weaker half of the class (median 5790).

Limit values: HTHS 3.7 mPa·s meets the 3.5 mPa·s minimum required for this class; CCS 6180 mPa·s at −30 °C is 94 % of the SAE limit (6600 mPa·s), leaving little cold-start reserve.

Based on its values it suits higher loads, towing or high-mileage engines. The specification or approval in your vehicle manual always has the final word.

The data sheet does not state sulphated ash, so we cannot compare it on this parameter.