Valvoline Advanced Full Synthetic 20W-50
Valvoline Advanced Full Synthetic 20W-50 is a 20W-50 engine oil (ACEA A3/B3, A3/B4 · API SP). According to the manufacturer's data sheet it has a viscosity of 169 mm²/s at 40 °C, 20.9 mm²/s at 100 °C, a viscosity index of 145 and HTHS of 5.4 mPa·s.
Data sheet ↗ Data verified: 19 Nov 2026
Parameters from the data sheet
| Parameter | Value | Class median 20W-50 i |
|---|---|---|
| Viscosity 40 °C | 169 mm²/s | 159 mm²/s |
| Viscosity 100 °C | 20.9 mm²/s | 19.8 mm²/s |
| Viscosity index | 145 | 140 |
| TBN | not stated | |
| CCS −15 °C | 8500 mPa·sThe manufacturer gives only a limit, "less than 8500", not a measured value. | 5027 mPa·s |
| Pour point | −24 °CThe manufacturer gives only a limit, "at most −24", not a measured value. | −35 °C |
| Flash point | not stated | |
| Density | 0.867 g/cm³ | 0.88 g/cm³ |
| HTHS 150 °C | 5.4 mPa·s | 5.4 mPa·s |
| Sulphated ash | not statedNot stated by the manufacturer. ACEA A3/B3 allows at most 1.5 %. |
All 20W-50 oils → See the class table for a detailed comparison with other oils.
Specifications and approvals
- Specification
- ACEA A3/B3, A3/B4 · API SP
- Oils by specification
Similar oils
Oils in the 20W-50 class with the closest parameters and the same specification.
- Red Line 20W-50ACEA A3/B3 · API SN
- AMSOIL OE 20W-50API SN PLUS
- PennGrade 1 High Performance 20W-50
- Royal Purple HPS 20W-50
- Valvoline VR1 Racing 20W-50
- Pennzoil 20W-50API SN
Oil analysis
We wrote this text by comparing the data-sheet values with the other oils in the 20W-50 class.
Valvoline Advanced Full Synthetic 20W-50 is a motor oil from Valvoline, viscosity grade 20W-50. In the database we compare it with 9 other oils in the 20W-50 class.
The oil meets API SP, ACEA A3/B3, ACEA A3/B4. API SP is the American specification for petrol engines with protection against low-speed pre-ignition (LSPI). ACEA A3/B3 is for petrol and diesel engines without a DPF with extended drain intervals. ACEA A3/B4 is for high-performance petrol and diesel engines without a DPF, with HTHS of at least 3.5 mPa·s.
Viscosity at 100 °C is 20.9 mm²/s, near the upper end of the 16.3–21.9 mm²/s range for the summer grade 50. Within its class the oil is on the thick side, with more reserve at high temperatures.
Average values: viscosity index 145 is close to the class middle (median 140); HTHS 5.4 mPa·s is close to the class middle (median 5.4).
Limit values: HTHS 5.4 mPa·s meets the 3.7 mPa·s minimum required for this class.
Based on its values it suits higher loads, towing or high-mileage engines. The specification or approval in your vehicle manual always has the final word.
The data sheet does not state TBN, Noack volatility and sulphated ash, so we cannot compare it on these parameters.