EuropeUSA 904 oils in 35 classes + 187 American oils in 10 classes SK · EN · DE · PL · Contact
Engine oil technical data · Castrol

Castrol EDGE 0W-40 A3/B4 (US)

Castrol EDGE 0W-40 A3/B4 (US) is a 0W-40 engine oil (ACEA A3/B4 · API SP). According to the manufacturer's data sheet it has a viscosity of 76 mm²/s at 40 °C, 13.3 mm²/s at 100 °C, a viscosity index of 180, a pour point of −45 °C and sulphated ash of 1.2 %.

Data sheet ↗ Data verified: 19 Nov 2026

✎ Found an error? Report it

Parameters from the data sheet

ParameterValueClass median 0W-40 i
Viscosity 40 °C76 mm²/s75.45 mm²/s
Viscosity 100 °C13.3 mm²/s13.4 mm²/s
Viscosity index180 186.5
TBNnot stated
CCS −35 °C5980 mPa·s5970 mPa·s
Pour point−45 °C−49 °C
Flash point210 °CMeasured in a closed cup (PMCC), so lower than the COC values in the other rows.225 °C
Density0.844 g/cm³0.841 g/cm³
HTHS 150 °Cnot statedNot stated by the manufacturer. ACEA A3/B4 requires at least 3.5 mPa·s.
Sulphated ash1.2 %

All 0W-40 oils → See the class table for a detailed comparison with other oils.

Specifications and approvals

Specification
ACEA A3/B4 · API SP
Oils by specification

Similar oils

Oils in the 0W-40 class with the closest parameters and the same specification.

Oil analysis

We wrote this text by comparing the data-sheet values with the other oils in the 0W-40 class.

Castrol EDGE 0W-40 A3/B4 (US) is a motor oil from Castrol, viscosity grade 0W-40. In the database we compare it with 7 other oils in the 0W-40 class.

The oil meets API SP, ACEA A3/B4, BMW LL-01, MB 229.5 and more (10 in total). API SP is the American specification for petrol engines with protection against low-speed pre-ignition (LSPI). ACEA A3/B4 is for high-performance petrol and diesel engines without a DPF, with HTHS of at least 3.5 mPa·s. MB 229.5 is the Mercedes-Benz approval for engines without a DPF with extended intervals. Renault RN0700 and RN0710 are Renault/Dacia approvals for petrol and older diesel engines.

Viscosity at 100 °C is 13.3 mm²/s, near the lower end of the 12.5–16.3 mm²/s range for the summer grade 40. Within its class the oil is on the thin side, which helps fuel economy.

Weaker values: viscosity index 180 is among the weakest in the class (median 186); pour point −45 °C is among the weakest in the class (median −50).

Limit values: CCS 5980 mPa·s at −35 °C is 96 % of the SAE limit (6200 mPa·s), leaving little cold-start reserve; sulphated ash of 1.2 % is higher; the oil is not intended for engines with a DPF.

Based on its values it suits engines without a DPF and everyday driving where fuel economy matters most. The specification or approval in your vehicle manual always has the final word.

The data sheet does not state HTHS, TBN and Noack volatility, so we cannot compare it on these parameters.