EuropeUSA 904 oils in 35 classes + 187 American oils in 10 classes SK · EN · DE · PL · Contact
Engine oil technical data · Valvoline

Valvoline Advanced Full Synthetic XL-III 0W-40

Valvoline Advanced Full Synthetic XL-III 0W-40 is a 0W-40 engine oil (ACEA A3/B3, A3/B4 · API SN). According to the manufacturer's data sheet it has a viscosity of 77 mm²/s at 40 °C, 13.5 mm²/s at 100 °C, a viscosity index of 180 and HTHS of 3.7 mPa·s.

Data sheet ↗ Data verified: 19 Nov 2026

✎ Found an error? Report it

Parameters from the data sheet

ParameterValueClass median 0W-40 i
Viscosity 40 °C77 mm²/s75.45 mm²/s
Viscosity 100 °C13.5 mm²/s13.4 mm²/s
Viscosity index180 186.5
TBNnot stated
CCS −35 °C6200 mPa·sThe manufacturer gives only a limit, "less than 6200", not a measured value.5970 mPa·s
Pour point−42 °CThe manufacturer gives only a limit, "at most −42", not a measured value.−49 °C
Flash pointnot stated
Densitynot stated
HTHS 150 °C3.7 mPa·s3.7 mPa·s
Sulphated ashnot statedNot stated by the manufacturer. ACEA A3/B3 allows at most 1.5 %.

All 0W-40 oils → See the class table for a detailed comparison with other oils.

Specifications and approvals

Specification
ACEA A3/B3, A3/B4 · API SN
Oils by specification

Similar oils

Oils in the 0W-40 class with the closest parameters and the same specification.

Oil analysis

We wrote this text by comparing the data-sheet values with the other oils in the 0W-40 class.

Valvoline Advanced Full Synthetic XL-III 0W-40 is a motor oil from Valvoline, viscosity grade 0W-40. In the database we compare it with 7 other oils in the 0W-40 class.

The oil meets API SN, ACEA A3/B3, ACEA A3/B4, MB 229.5 and more (10 in total). API SN is an older American specification for petrol engines. ACEA A3/B3 is for petrol and diesel engines without a DPF with extended drain intervals. ACEA A3/B4 is for high-performance petrol and diesel engines without a DPF, with HTHS of at least 3.5 mPa·s. MB 229.5 is the Mercedes-Benz approval for engines without a DPF with extended intervals. Renault RN0700 and RN0710 are Renault/Dacia approvals for petrol and older diesel engines.

Viscosity at 100 °C is 13.5 mm²/s, near the lower end of the 12.5–16.3 mm²/s range for the summer grade 40. Within its class the oil is on the thin side, which helps fuel economy.

Average values: HTHS 3.7 mPa·s is close to the class middle (median 3.7).

Weaker values: viscosity index 180 is among the weakest in the class (median 186).

Limit values: HTHS 3.7 mPa·s meets the 3.5 mPa·s minimum required for this class.

Based on its values it suits everyday driving where fuel economy matters most. The specification or approval in your vehicle manual always has the final word.

The data sheet does not state TBN, Noack volatility and sulphated ash, so we cannot compare it on these parameters.