EuropeUSA 904 oils in 35 classes + 187 American oils in 10 classes SK · EN · DE · PL · Contact
Engine oil technical data · Kendall

Kendall GT-1 Endurance 5W-20

Kendall GT-1 Endurance 5W-20 is a 5W-20 engine oil (API SN · ILSAC GF-5). According to the manufacturer's data sheet it has a viscosity of 49.9 mm²/s at 40 °C, 8.6 mm²/s at 100 °C, a viscosity index of 150, HTHS of 2.6 mPa·s, a TBN of 8 mg KOH/g, a pour point of −39 °C and sulphated ash of 0.96 %.

Data sheet ↗ Data verified: 19 Nov 2026

✎ Found an error? Report it

Parameters from the data sheet

ParameterValueClass median 5W-20 i
Viscosity 40 °C49.9 mm²/s47.75 mm²/s
Viscosity 100 °C8.6 mm²/s8.4 mm²/s
Viscosity index150 157.5
TBN8 mg KOH/g9.1 mg KOH/g
CCS −30 °C6150 mPa·s4397 mPa·s
Pour point−39 °C−42 °C
Flash point218 °C225 °C
Density0.863 g/cm³0.85 g/cm³
HTHS 150 °C2.6 mPa·s2.7 mPa·s
Sulphated ash0.96 %0.815 %

All 5W-20 oils → See the class table for a detailed comparison with other oils.

Specifications and approvals

Specification
API SN · ILSAC GF-5
Oils by specification

Similar oils

Oils in the 5W-20 class with the closest parameters and the same specification.

Oil analysis

We wrote this text by comparing the data-sheet values with the other oils in the 5W-20 class.

Kendall GT-1 Endurance 5W-20 is a motor oil from Kendall, viscosity grade 5W-20. In the database we compare it with 22 other oils in the 5W-20 class.

The oil meets API SN, ILSAC GF-5, Chrysler MS-6395, Ford WSS-M2C945-A. API SN is an older American specification for petrol engines. ILSAC GF-5 is an older US–Japanese specification for fuel-efficient petrol engines. Chrysler MS-6395 is the Stellantis approval for Jeep, Dodge, RAM and Chrysler petrol engines. Ford WSS-M2C… approvals apply to specific Ford engines, check them against the owner's manual.

Viscosity at 100 °C is 8.6 mm²/s, near the upper end of the 6.9–9.3 mm²/s range for the summer grade 20. Within its class the oil is on the thick side, with more reserve at high temperatures.

Weaker values: viscosity index 150 is in the weaker half of the class (median 158); HTHS 2.6 mPa·s is among the weakest in the class (median 2.7); TBN 8 mg KOH/g is among the weakest in the class (median 9.1); CCS 6150 mPa·s is among the weakest in the class (median 4322); pour point −39 °C is in the weaker half of the class (median −42); flash point 218 °C is among the weakest in the class (median 228).

Limit values: HTHS 2.6 mPa·s meets the 2.6 mPa·s minimum required for this class; CCS 6150 mPa·s at −30 °C is 93 % of the SAE limit (6600 mPa·s), leaving little cold-start reserve; sulphated ash of 0.96 % is higher; the oil is not intended for engines with a DPF.

Based on its values it suits engines without a DPF and higher loads, towing or high-mileage engines. The specification or approval in your vehicle manual always has the final word.

The data sheet does not state Noack volatility, so we cannot compare it on this parameter.